Address Mounting Blocks

Address Mounting Blocks Toll GOT-VENTS468-8368 Mon-Fri 8am-5pm Mountain Time
Home | Products Photo Gallery | About Us Contact Us | | Specials | View Cart
Address mounting blocks are a great way to finish off the front of your home. We have 2 sizes, several mounting flange options and 70+ colors available. Can be used with any exterior finish.
Our mounting blocks compliment your exterior facade.
A great way to make your house numbers stand out!


(House Numbers Not Included)


* Each address mounting block comes with a standard nailing flange, an extended standard nailing flange a J-channel or an outside nailing flange.

Address Mounting Block with Standard Nailing FlangeSee drawings below.

* Use the standard nailing flange with stucco, fiber cement siding (Hardie Plank), composition siding or wood siding.
* Use the extended standard nailing flange with brick, rock or stone.
* Use the J-channel with vinyl siding, aluminum siding or steel siding.
* Use the outside nailing flange when cutting into an existing exterior finish.
* A variety of color choices enable us to match address mounting blocks to any project.


Standard Nailing Flange
Extended Standard Nailing Flange
J-Channel
Outside Nailing Flange

We manufacture AND ship out in 4 business days or less!

© 2014 American Louver And Vent Company

Address Mounting Block with Extended Standard Nailing Flange Address Mounting Block with J-Channel Address Mounting Block with Outside Nailing Flange

Source: www.alvcompany.com

Authenticated 1946 Ad Ford Station Wagon Classic Car Automobile Convertible Wood Siding Red - Original Print Ad
Home (Authenticated)
  • Product Type: Original Print Ad; Color
  • Grade: Very Fine ++
  • Dimensions: Approximately 10 x 13.5 inches; 25 x 34 cm
  • Authentication: Dual Serial-Numbered Certificates of Authenticity w/ Full Provenance
  • Packaged in custom sleeve w/ archival black board (great for display, gift-giving, and preservation)

You might also like:

Scalloped Mounting Block (115185)‪
Scalloped Mounting Block (115185)‪

Probably impossible to fireproof any wood deck.

Some exotic hardwoods will just smoulder, but the cost will not be practical. IMHO you have two choices. The deck could be constructed of fire resistant composite materials, similar to how some siding is fabricated these days. Your other choice would be a metal decking consruction. It would look like the grills on a French drain. Just out of curiosity, what material have your neighbors constructed their decks out of?

Ogdensburg home rehabilitation program gears up for phase two, on schedule  — WatertownDailyTimes.com
Some homes will receive extensive and visible rehabilitation, including the installation of vinyl siding, roofing and windows. Other homes won't have an obvious exterior update but will have new furnaces or flooring put in.


Related posts:

  1. Wood Siding on Interior Walls
  2. Wood siding material cost
  3. Vinyl siding Mounting blocks

  • Avatar Jeff How do you replace motor mounts on a 1987 Chevrolet S-10?
    Oct 06, 2010 by Jeff | Posted in Chevrolet
    • Jack and support both sides, !!DO NOT leave car on jacks!! Cinder blocks work well, jack stands are best
      Loosen the mounts on both sides,
      place a floor jack with a wood plank under oil pan and lift,
      remove one side, usually 3 bolts, tighten bolts,
      replace other side,
      lower engine onto mount,
      replace mounting bracket bolts and tighten.

  • Avatar burn_to_blue Best way to mount unmounted stamps?
    Jan 19, 2008 by burn_to_blue | Posted in Hobbies & Crafts

    How does a person go about mounting unmounted rubber stamps on the wooden blocks? Just Super Glue or something like that, or is there a better way?

    • It depends on what the stamp is made from, old-fashioned rubber or newer polymer. Two-sided tape is going to be the best way if you really want them mounted on wood blocks, but that may not be necessary. If you check the …way to do any kind of stamping. Rubber cement and super glue are positively NOT the way to go.

      You can learn more about unmounted stamps at our Amazing Arts Yahoo User Group here: call it Stamping Naked =)

  • Avatar doccizpagan 1991 Buick Park Ave. motor mounts,please read on...?
    Dec 02, 2007 by doccizpagan | Posted in Maintenance & Repairs

    I have a broken drive motor mount,first I can't seem to find the part,second,I have no clue how to fix it.Most detailed answer will get the 10.

    • These cars tend to break the front transmission mount which is located on the drivers side near the radiator on the front rail of the engine cradle (front sub-frame). when this mount breaks the engine jumps on accel in d …your local auto parts for $30-$40 dollars, it would be called the front transmission mount and it's in the left front position.
      Professional replacement woul be about $130.00 so way your options. Hope this helps.