The Right Tools for Vinyl Siding Installation

In vinyl siding installation, you need the right tools either you go for DIY or hire a professional installer. Many choose the vinyl as a siding compared with other sidings because of its simplicity and durability. Vinyl sidings are also easy o install, repair and manage. Either you are planning to install the vinyl siding for the first time or renovate your current home; you still need to have the following tools to make your project successful. Review the tools you will need for the project before you install or replace vinyl siding.

The following are the basic tools and kits for vinyl siding installation.
• Snap-lock punch – this is helpful to punch lugs and make tabs in the cut edge of a cladding panel used as a finishing course. It works best for aluminum vinyl but not for steel. Also, it is essential when installing sidings below windows and at a wall’s upper edge.
• Nail hole slot punch – this is required especially when you need to add or expand a hole.
• Zip lock tool – this tool will help you to remove or replace a panel of the current siding. At the same time, you can use this tool to relock a panel for installation. It also unlocks the channels of installed vinyl siding.
• Ladders and scaffolding – you will need this in case the job is complex to reach the higher sides of your house.

There are other basic tools that you will need for cutting, trim siding, shaping the siding, and more include the following:
• Eye protection – just for extra protection especially when cutting and shaping the vinyl.
• Utility knife – this is useful when part of a vinyl is stuck or it is too long.
• Tin snips – this tool can cut vinyl easily and can shape it speedily.
• Fixed or hand-held power saw – this is the basic tool that you will need in order to install the vinyl siding. You can use a hand-held saw or a bench saw. Either of the two can be used, as long as you use a fine blade saw.
• Carpenter Square – one of the important tools to have an accurate measure for cutting marks

All of these tools are available at any hardware store and a must have, for without these the installation or repair can be a hassle. Now you can start installing or repairing the vinyl sidings in your home. Of course, while working you should remember of safety precautions from using the tools and while on the process since there are certain aspects that you should know and you can inquire professionals for other practices. In the end, you will see that it is all worth it.

Commonly, you will need to have a hammer, screwdriver, pliers, chalk line, tape measure, level and Metal Square and a saw for vinyl siding repair or build something at home. However, vinyl siding installation requires for more tools. You will only be prepared for the installation of vinyl siding when you have the right tools or you can hire expert installer at

Source: www.thishandyman.com

You might also like:

Vinyl Siding Installation
Vinyl Siding Installation
Vinyl siding
Vinyl siding

Wood siding installation vs vinyl difficulty lev

I've worked with vinyl siding installation. As I get to remodelling houses for sale, rather than remodelling for rental, I'll need to learn wood siding. Is it easier or harder to do right? Can it be a one man job? I like to work alone, even if it makes things a little harder, but only if the job is still doable. I imagine maybe the lower parts of the house could be one man, but as you get higher up on the ladder you need two people?

Ogdensburg home rehabilitation program gears up for phase two, on schedule  — WatertownDailyTimes.com
Some homes will receive extensive and visible rehabilitation, including the installation of vinyl siding, roofing and windows. Other homes won't have an obvious exterior update but will have new furnaces or flooring put in.


Related posts:

  1. Tax deduction vinyl siding
  2. D4 traditional Vinyl Siding
  3. Mastic Ovation Vinyl Siding

  • Avatar Eddie Pat Where can I learn how to install HardiPlank siding?
    May 06, 2006 by Eddie Pat | Posted in Do It Yourself (DIY)

    I have 30 yr. old shiplap on my detached garage and would like to try to replace it with hardiplank....but I don't have much carpentry experience.

    • As a professional it is not difficult however, it is very dusty and definitely not a one person job. Start with installing your 5/4 boards on the corners of the house. Then make sure your bottom board (the first one you …edge of the first board. I would make it 7" long and that will let you maintain the same space between each row. Set the next course on the top (the bottom of the "T") and nail. Keep going until your done.

  • Avatar melinda s What size steel beam would replace a 4x12x20 wood beam?
    Feb 07, 2012 by melinda s | Posted in Do It Yourself (DIY)

    The beam supports one side of a patio roof (17x17) that is made of shiplap sheathing covered with fiberglass shingles.

    • You need to go to a steel beam supplier and take the following information with you. They can determine the size you'd need. First take a picture of it underside and outside of the porch. They will need to know how long …br />
      The 1st responder suggested talking to an architectural engineer. No such thing. There are architecs that design and engineers that calculate loads.

      Hope this helps and isn't too confusing.

  • Avatar Deadsion Another Wooden Fence?
    Jun 25, 2007 by Deadsion | Posted in Do It Yourself (DIY)

    Anyone know how to or know of a website that explains how to make a board-on-board fence. I want to avoid having those 1-2 inch spaces between the fences after the boards shrink in a normal fence

    • Use 'shiplap' boards (they have a half inch rabbit on both sides).

      When you place them, they will overlap a half inch on both sides and the overlap will accommodate shrinkage.

      paint or stain …ge does not show a raw wood seam.

      Do not fasten at each edge, as shrinkage will then tend to split a board.

      If you use 6 inch boards, use 2 fasteners about an inch and a half from each edge.