Aluminum siding vs brick siding

Install aluminum siding

A comparison of aluminum siding vs brick siding to help you choose which is best for your home

  • Do you like this article?

Get Siding Estimates

If you are thinking of improving the exterior of your home then many siding options are available for your consideration. The choices include aluminum, stone, vinyl, brick and wood. With such a wide range of available materials, you should compare aluminum siding vs. brick siding to find the material that is best for your home. It's a smart move to learn about the pros and cons of different siding types before making a decision.

Aluminum siding
Several good reasons for choosing aluminum siding include:

  • Inexpensive and low maintenance compared to other types of siding
  • Easy to install, durable, fireproof and waterproof
  • Rust, mold and termite resistant

Install brick sidingThe main drawback of using aluminum is that it gets easily damaged. Aluminum is a relatively soft metal, so it's prone to dents and scratches; you could damage the aluminum just by leaning a ladder against the house. In addition, heavy rain, strong winds and hail make the aluminum noisy; hail also causes dents.

Brick siding
Like aluminum, brick siding is also low maintenance, but is more expensive to install than aluminum due to the higher level of skill required for installation. Bricks can withstand all types of weather conditions, are durable and strong and offer a more appealing and traditional look. Brick also provides a home with good insulation. This insulation protects the home from outside noise and from extreme hot or cold temperatures. This type of siding also comes in many patterns, so you can create an original and imaginative design. The only real disadvantages to using brick are the expense and the installation time.


You might also like:

Insulated Vinyl Siding Vs. Hollow …
Insulated Vinyl Siding Vs. Hollow …

Thanks for all the thoughts

I've decided to bite the bullet and do a proper mini-pole building with PT posts set 3 feet into the ground and 2 x 6 strapping carriage bolted to the frame on 12" spacing where the cow's weight might push the walls, 24" spacing screwed above that. Bottom 2 x 6 PT, the rest just fir.
I'll probably do corrugated metal siding even though it's a bit cold because the 2 x 6 framework will act as a buffer where she would lean against it. I have a really nice heavy-duty electric shear so cutting the panels shouldn't be too tough, just fiddly.
Simple shed roof similar to the walls with some overhang

As FixitMike says, the forces tend to

Pull this structure from the wall and ties must take the loads. For loads near the outside edge of this deck, roughly 62% of that load will be the force pulling it off the wall. The lag bolts will probably be every 16 inches, staggered to hold the ledger. I would NOT count on joist hangers in tension for the joists. Those are meant strictly for vertical loads. As a minimum I would use Simpson strapping around the back of the ledger running six inches or so above and below the joist for tension. Nailing decking with tht on top would be a problem so might have to wrap it behind the ledger and run a foot out under the joist only

Small Parts 6061 Aluminum U-Channel, Unpolished (Mill) Finish, Extruded, T6 Temper, AMS QQ-A-200/ASTM B221, Equal Leg Length, Rounded Corners, 1.75" Wall Thickness, 12" Length
BISS (Small Parts)
  • 6061 aluminum provides good corrosion resistance, strength, machinability, and weldability
  • Meets AMS-QQ-A-200 and ASTM B221 specifications
  • Unpolished (mill) surface has no finish
  • Extruded into the shape by compressing metal and pushing it through a die
  • Heat treated for increased strength
General Electric General Electric GE22749 Max Extra Siliconized Acrylic Caulk, 5.5-Ounce, Crystal Clear
Home Improvement (General Electric)
  • Exceeds ASTM C834 for better flexibility in most temperatures
  • Ethylene glycol-free
  • TYPICAL USES: Around doors, windows, siding, trim, molding, baseboards and vents
  • ADHERES TO: Most metal, glass, tile, wood, metal, drywall, plaster, masonry and some plastics
  • Specifications: Exceeds ASTM Spec C-834, Type C, Grade 0C requirements
FM DX Antenna Co FM Omnidirectional HD Stereo Reception Antenna
Home Theater (FM DX Antenna Co)
  • This horizontal FM antenna gives great results if you want to pick up FM radio stations from all directions whether mounted inside or outside.
  • You ll be pleased with the size of this omnidirectional FM antenna as it is big enough to pull in distant FM signals but small enough to mount inside or stealthily...
  • Built to last for years outside but small enough to bring inside. You ll be able to pick up distant FM signals in your attic or crawl space like you never have before.
  • The folded dipole is the most popular FM omnidirectional design in Europe and is a proven performer.
  • This FM antenna is extremely well-built; you will be pleased with the construction quality allowing years of great FM reception.

Related posts:

  1. Metal Siding Sheet Pricing
  2. Metal siding San Antonio
  3. Metal Siding Houston TX
  4. Metal siding in Oregon